Fanuc 21i-t parameter manual

Upload aoaby. Embed Size px x x x x

Warning Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other conditions that could cause personal injury exist in this equipment or may be associated with its use. In situations where inattention could cause either personal injury or damage to equipment, a Warning notice is used. Caution Caution notices are used where equipment might be damaged if care is not taken. Note Notes merely call attention to information that is especially significant to understanding and operating the equipment. This document is based on information available at the time of its publication.

Fanuc 21i-t parameter manual

Follow along with the video below to see how to install our site as a web app on your home screen. Note: This feature may not be available in some browsers. This website or its third-party tools process personal data e. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page. To find out more about the categories of personal information collected and the purposes for which such information will be used, please refer to our privacy policy. You accept the use of cookies or other identifiers by closing or dismissing this notice, by scrolling this page, by clicking a link or button or by continuing to browse otherwise. How to install the app on iOS. Log in Register. Search titles only.

This eliminates changes in feedrates between blocks. NOTE When PPD is set to 1 and the absolute position display is preset fanuc 21i-t parameter manual one of the following, the relative position display is also preset to the same value as the danmachi loki position display: 1 The manual reference position return 2 Setting of a coordinate system by G92 G50 for T series G code system A.

.

Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other conditions that could cause personal injury exist in this equipment or may be associated with its use. In situations where inattention could cause either personal injury or damage to equipment, a Warning notice is used. Notes merely call attention to information that is especially significant to understanding and operating the equipment. This document is based on information available at the time of its publication. While efforts have been made to be accurate, the information contained herein does not purport to cover all details or variations in hardware or software, nor to provide for every possible contingency in connection with installation, operation, or maintenance.

Fanuc 21i-t parameter manual

Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other conditions that could cause personal injury exist in this equipment or may be associated with its use. In situations where inattention could cause either personal injury or damage to equipment, a Warning notice is used. Notes merely call attention to information that is especially significant to understanding and operating the equipment. This document is based on information available at the time of its publication. While efforts have been made to be accurate, the information contained herein does not purport to cover all details or variations in hardware or software, nor to provide for every possible contingency in connection with installation, operation, or maintenance. Features may be described herein which are not present in all hardware and software systems. GE Fanuc Automation assumes no obligation of notice to holders of this document with respect to changes subsequently made. GE Fanuc Automation makes no representation or warranty, expressed, implied, or statutory with respect to, and assumes no responsibility for the accuracy, completeness, sufficiency, or usefulness of the information contained herein. No warranties of merchantability or fitness for purpose shall apply.

Kotaro fuma

MOU In program restart operation, before movement to a machining restartpoint after restart block search:. These parameters set the M codes that call the custom macros of programnumbers through The parameters of the spindle amplifier with serial interface can be changed after thesystem starts. NE9 Editing of subprograms with program numbers to : Not inhibited1 : InhibitedThe following program editing during operation is invalid. Lista 26 10 1 Lista 26 10 1. In polar coordinate, cylindrical, and involuteinterpolation, the maximum feedrate for all axes specified inparameter No. Example of setting: For onesystem control When the fourth axis is controlled as the Baxis, set 4 in this parameter. NOTE Setting value 0 is invalid. Parameters of automatic tool compensation T series andautomatic tool length compensation M series , This parameter sets the feedrate of a normal direction control axis that isinserted at the start point of a block during normal direction control. Stopped during cutting feed Stopped during rapid traverse. The tool life management function allows the user to specify a tool life either as a use duration or use count for each tool group. When a command specifying a speed exceeding the maximum speed ofthe spindle is specified , or the speed of the spindle exceeds the maximumspeed because of the spindle speed override function, the spindle speed isclamped at the maximum speed set in the parameter. Set the machine coordinates of theboundaries in the positive direction Xp, Yp, and Zp using parameterNo. The bits correspond to the following signals:.

.

They set the distance with sign between the measurement reference position and sensor contact surface. When the waveform diagnosis function is used, this parameter sets thetime form the output of a servo alarm until data collection. OPM Operating monitor 0 : Not displayed 1 : Displayed OPS The speedometer on the operating monitor screen indicates: 0 : Spindle motor speed 1 : Spindle speed NPA Action taken when an alarm is generated or when an operator message is entered 0 : The display shifts to the alarm or message screen. Set the time elapsed from the execution of the S function up to thechecking of the spindle speed arrival signal. This parameter is used to check the difference in phase in synchronization control and to confirm the completion of synchronization in the serial spindle synchronization control mode. ZCL Local coordinate system when the manual reference position return isperformed0 : The local coordinate system is not canceled. If this parameter is set to 1 when using the serial spindle andanalog spindle at the same time, the analog spindle is setthe first axis. Position control loop gain for the spindle and tapping axis in rigid tapping common to all gears. Error pulse between two spindles when synchronizing phases in the serial T, M spindle synchronization control mode [Data type] Byte [Unit of data] Pulse [Valid data range] 0 to Set the difference in error pulses between two spindles when synchronizing phases in the serial spindle synchronization control mode. Usually, parameter No. Confirmthat the output voltage is 10V. M Critical angle subtended by two blocks for automatic corner deceleration for lookahead control [Data type] 2word [Unit of data] 0. This parameter sets the speed of retraction to point R when no address I isissued in a peck drilling cycle of a small diameter.