Ikea idasen

Have a question about this project? Sign up for a ikea idasen GitHub account to open an issue and contact its maintainers and the community. Already on GitHub? Sign in to your account.

If you are not using an ESPHome Bluetooth Proxy, you need to keep bluetoothctl or any other Bluetooth Agent open during the integration setup, or it will fail to authenticate with the desk. The connection process is also less reliable than with ESPHome, so you may need to retry a few times until it succeeds. This is due to a limitation in the third-party Bluetooth implementation used by Home Assistant. Also, if not using an ESPHome Bluetooth Proxy, you may experience the desk becoming unavailable and needing re-pairing after a restart of Home Assistant or a reload of the integration. If the desk is not listed as paired, repeat the command several times while entering pairing mode on the desk.

Ikea idasen

.

The Bluetooth settings menu on Gnome also works and I assume any Bluetooth management UI will too, as long as it starts ikea idasen auth agent. I'll have to dig a bit more.

.

But there is one major problem — the IKEA desk have no memory and I cannot set it to a predefined fixed height. The problem is that my neck and back are not very happy about that fact, as they started to shudder and hurt. I had read somewhere about the standing desks and their benefits, so I dig into the topic more and then I decided to go for it. It turns out that the IKEA is selling one of the best desks with motors, so you can have a stand desk and when you get tired to — lower it down and to sit on a chair as usual and vice versa. Quick tip here, if you decide to buy similar standing desk from IKEA have in mind that they have two very similar models:. The IDASEN standing desk is having up and down switch and Bluetooth support, but as I said in the beginning, there is no memory and you cannot move the desk to a certain fixed height.

Ikea idasen

This sturdy desk is built to outlast years of coffee and hard work. You get a generous work surface and a clever solution to keep cords in place underneath. Read about the terms in the warranty brochure. The veneer surface is durable, stain resistant and easy to keep clean. Possible to separate for recycling or energy recovery if available in your community. Check regularly that all assembly fastenings are properly tightened and retighten when necessary.

Hand winding machine

The current height of the desk, in meters. Skip to content. Improve Ikea Idasen config flow error messages The script sets the position, waits for 5 seconds to give it a chance to start moving and then the wait template checks that it has stopped moving. If I pair it manually first using bluetoothctl , then HA is able to setup the integration and connect. Is the light blinking every couple seconds? This is still an issue All reactions. I've also tried physically placing my HA server right below the desk controller. Connecting and pairing manually with bluetoothctl worked for me too, thanks! Sign up for a free GitHub account to open an issue and contact its maintainers and the community. They were probably spotted at some point by the RPI radio. I think I have a similar issue, but a different error entry in my log. Sign up for free to join this conversation on GitHub. The connection process is also less reliable than with ESPHome, so you may need to retry a few times until it succeeds. For that, press the small button with the Bluetooth logo on the controller until it starts blinking about 3 seconds.

This sturdy desk is built to outlast years of coffee and hard work.

Reload to refresh your session. I'm justing the built-in bluetooth of the RPI 4 which is one floor down from where the desks are. I was worried I'd have to do that each time after Home Assistant restarts, since the desk cover entity becomes unavailable after rebooting, but reloading the integration was enough to bring the entity back. I just updated to It repeats that pattern for a while. Then if it is still out of position it will retry up to 5 times. Yes, the desk keeps going offline, and needs an integration reload to work again. There hasn't been any activity on this issue recently. Sign up for free to join this conversation on GitHub. Glad to know it works as a workaround. Here's my log: Logger: homeassistant. Regarding the position, yeah, that is a known issue with the underlying mechanism that controls movement, and I am not sure it will be possible to fix since there is a delay between sending the command for it to stop and it actually stopping. The text was updated successfully, but these errors were encountered:.

2 thoughts on “Ikea idasen

Leave a Reply

Your email address will not be published. Required fields are marked *