Ipod nano 1 battery

I recently found an old iPod Nano 1st Generation that was sitting in a drawer, collecting dust since around or When it was in use, it was slightly damaged with a small dent on one side of the back. I also noticed the back was slightly coming off on the opposite side of the dent, but I assumed it was just because of the dent. Upon charging it, the opening got somewhat worse, ipod nano 1 battery, so I unplugged it remember pin?

The rear panel is secured to the front case by eleven clips permanently attached to the rear panel. These clips lock onto small tabs machined into the front case. To free the tabs, they must be pushed down and away from the iPod's case. Note the location of all tabs on the rear panel. When using an iPod opening tool to free the rear panel, be sure to work the tool at the location of these clips. Opening the iPod can be challenging.

Ipod nano 1 battery

Enter your email address below, and we will notify you when this product is back in stock. This iPod nano 1st Gen replacement battery is what you need to bring your dead iPod back to life! Battery degradation is an inevitable part of your iPod's lifespan — extend it with this new replacement battery compatible with the first generation iPod nano. Then use your device until it shuts off due to low battery. This replacement battery may be a slightly more snug fit than the original due to a small variation. Learn more about safe lithium-ion battery handling and proper disposal. This product can expose you to chemicals including lead which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www. All our products meet rigorous quality standards and are backed by industry-leading guarantees. Condition: New.

Opening the iPod can be challenging. Do not attempt to handle the battery yourself as it is now in poor condition and further bending, squeezing or puncturing of it is definitely not good!

.

The rear panel is secured to the front case by eleven clips permanently attached to the rear panel. These clips lock onto small tabs machined into the front case. To free the tabs, they must be pushed down and away from the iPod's case. Note the location of all tabs on the rear panel. When using an iPod opening tool to free the rear panel, be sure to work the tool at the location of these clips. Opening the iPod can be challenging. Don't get discouraged if it takes you a few tries before the iPod is opened. Insert the large iPod opening tool into the seam between the front case and rear panel of the iPod, below the dock connector.

Ipod nano 1 battery

However, a variety of more affordable third-party services also are available. Third-parties offer battery replacement services for considerably less than Apple charges and often sell "longer runtime than stock" batteries for self-installation as well. If you are not sure which iPod nano you have, one way to externally identify these models is via a unique model number on the back of the device. These models also can be differentiated by serial number with Everyi. Like the model number, the serial number is toward the bottom on the back of the device or under the "teeth" on the clip and also is available when plugged into a computer on the "Summary" tab in a modern version of iTunes among other methods. In addition to its serial number, Everyi. Replacing the battery in the iPod nano models -- regardless of generation -- is difficult and requires soldering.

Vera maari office

Hold wire until solder has set. Lifetime Guarantee. View in context. Initiate a return here. Uwe von Ditfurth - Mar 21, Reply. Gently lift up on the dock connector end of the logic board to ensure the logic board is free. To open the solder holes, open a safety pin and push it against the solder blocking the hole. The large iPod opening tool is no longer needed to gain access to the left side of the iPod. The "battery" issue I have is that the battery is expanding inside the case. Essential Electronics Toolkit. Disconnecting the following two ribbon cables may be challenging. Step 1 Rear Panel. Add Comment.

Enter your email address below, and we will notify you when this product is back in stock. This iPod nano 1st Gen replacement battery is what you need to bring your dead iPod back to life!

No that's what I call environmental awareness! Learn more Sign up. Grasp the end of the logic board near the battery connector with one hand, and hold onto the rest of the iPod with your other hand. Zachary Rushworth - Oct 26, Does anybody know how to safely remove the battery with the lowest risk of damage to the iPod? Rotate the battery toward the logic board and place it flat in its void, bending the cables as necessary. Customer Reviews. Despite your nostalgia for your iPod, a swollen battery should be considered a fire risk and needs to be carefully disposed of. Posted on Aug 10, AM. The rear panel is secured to the front case by eleven clips permanently attached to the rear panel. Use a spudger to flip up the black plastic tab holding the orange click wheel ribbon in place. Similar questions I have a 16G, 6 generation ipod touch that I purchased in In order to avoid damage, lift the solder tip off the connection as soon as the solder melts and the lead slides out. I thought this was a bit difficult, mainly the initial separation and the soldering. For all newbies, make sure that your soldering spots are neat and clean.