Lawn mower starter cord replacement

With perfect weather, you plan to go out to give your lawn a nice trim. You use a push mower that has never let you down in all these years. The other end is spinning back into the starter assembly.

This DIY lawn mower repair guide has instructions for how to replace a lawn mower starter rope. Over time, the starter rope can wear out and eventually break, and the mower won't start. You can replace a broken recoil starter rope with a manufacturer-approved replacement part by following the steps below. Remove the dipstick tube from the engine and plug the hole with a paper towel to keep debris from falling into the engine. Remove the bolts securing the blower housing to the engine and remove the housing from the engine.

Lawn mower starter cord replacement

Now you could let the pull cord snap just before you want to start mowing, but this makes for a long day. Pull cords on lawn mowers are usually made of a pretty strong nylon rope. While nylon rope is a sturdy material, the friction between the rope and the starter housing will eventually wear it down. So, no matter how careful you are with your pull starter, the time will come when your cord will wear down and need replacing. After all, the cord is designed to be a certain length to turn over the engine and get the fuel pump pumping and the coil sparking the spark plug. You should be able to find this information in your user manual. Before I tackle any repair with my lawn mower, I always pop off the spark plug to avoid any unexpected accidents. So, pull off the spark plug cable and tuck it out of the way. The first job is to remove the starter assembly from your lawn mower. My starter assembly is attached to the lawn mower with four bolts that can be removed with either a flathead screwdriver or a nut driver. So, inspect your mower and see what tool you need to use, then remove the mounting bolts and lift the starter assembly off your lawn mower.

A lawnmower that has been in use for a very long time has a high risk of getting its pull cord damaged. To do this, lawn mower starter cord replacement, first put a mark on this rope according to the length required and then cut the end using a pair of scissors.

Own a lawnmower long enough, and eventually, you will experience small engine pull cord failure. Whether your lawnmower pull cord has seen its fair share of uses or it fails before its time due to quality, these seven simple steps will show you exactly how to replace pull cord on mowers to get you back up and running before your next mowing mission. SGT KNOTS Dacron Polyester Pull Cord is the heavy-duty, ultra-reliable replacement pull cord and starter rope every landscaping business, homeowner, or neighborhood lawn care kid should have hanging in their garage for on-the-fly fixes. This cord is as cost-effective as it is reliable with a Dacron polyester solid-braid construction resistant against abrasion and wear. Snag this cord in either 4, 5, or 6 diameters and lengths of 10ft and 25ft, or spools of 50ft, ft, and 1,ft for a never-ending supply of replacement pull cord perfect for everything from mowers, generators, leaf and snow blowers, and more. Now that you know how to replace a mower pull cord, you can move onto your next DIY repair or improvement project.

At some point, all household maintenance tools are subject to wear and tear, and your lawn mower is no exception. A broken lawn mower pull cord is a pretty common problem. And fortunately, it is easy to get done DIY. When a pull cord is broken, it means that the starter rope has detached from the rest of the cord. The starter rope is the visible part of the cord. You can access it from outside of the mower. Make sure you replace it if it breaks.

Lawn mower starter cord replacement

The pull cord is used to start the lawn mower; it can often become broken or need replacement. Additionally, make sure you have a large table for the replacement and a rag nearby for wiping off any grease and oil. Make sure the the engine is off and the spark plug wire is removed and away from the spark plug before begining. Use a Phillips 2 screwdriver to remove the two 25mm screws on top of the engine cover.

Gta myths

But, first of all, we need to find the starter disk on the lawnmower. August 11, Logan Cook says:. Some of the are listed under:. Follow the step-by-step guide provided in the blog post to ensure a successful replacement. December 26, at am. Thank you, David! This post covers pull cord replacement pretty well. Brake — Check that the bail lever is releasing the flywheel brake. The cord-replacement process is just slightly longer. Next, cut the knot off inside the pulley with scissors and pull the cord from the starter assembly. Monica Dixon says:.

Are you struggling with a broken pull cord on your lawnmower?

To reinstall the engine shroud: 1. I appreciate your perspective. Fit both pawls and cap, and tighten the bolt. January 17, at pm. Too much oil is also bad for the engine. September 17, at pm. Connie Cook says:. Why does my lawn mower stall? Friends used to call me the "lawn mower guru" hence the site name , but I'm anything but. How long is the lawnmower cord supposed to be? If your pull cord is hard to pull stiff , make sure the bail lever is held during the starting process. View all. Using a fine screwdriver, feed the cord end into the blower assembly housing cord hole. SGT KNOTS Dacron Polyester Pull Cord is the heavy-duty, ultra-reliable replacement pull cord and starter rope every landscaping business, homeowner, or neighborhood lawn care kid should have hanging in their garage for on-the-fly fixes. Working with recoil springs can be dangerous; removing the pully from the assembly comes with the risk of the spring breaking free.