Playstation 2 laser replacement
Replace the laser assembly in your optical disc drive. Replacing the laser requires you to have or purchase a new laser. Flip the PlayStation 2 over so it lays with the bottom of the device facing upwards. Some models have a different number of playstation 2 laser replacement and feet.
Use this guide to help identify which optical laser lens replacement will fit your PlayStation 2 console. Note: Replacing the laser lens will normally require a soldering iron to remove an anti static point solder blog before install. Laser lens models can normally be identified from the console model but it is always advisable to physically remove and check the old laser prior to ordering any replacement to ensure that it is the model you expected, and that the new part is the same model or listed as a compatible replacement for the model of laser you have. Lasers will need to be fitted to the deck unit inside the console, this requires some additional rebuilding, unscrewing runners to remove the old laser and put the new one in place. This is only a few additional steps but if you are less confident with completing the repair, or you believe other parts of the laser mechanism is not working properly, you can opt to purchase the deck with the laser pre-installed. Remember the anti static solder blob will still need to be removed prior to installation or the laser will not operate, this applies to all laser units, whether attached to the deck or not. This site uses cookies to provide you with a great user experience, by using ZedLabz.
Playstation 2 laser replacement
Disconnect all cables from the console and flip the unit over to reveal its base. Locate the 6 feet on the base of the unit. Pry them off using a spudger to reveal the screws. Note: One of the feet is located under the sticker shown in the photo. Removing this sticker will void any warranty with Sony. Remove all six 4. Starting at the corner at which the power and Ethernet ports are located, pry open the outer shell using a spudger and continue around the entire unit. Note: You may use your hands for additional force to separate the two pieces of the outer shell. Take the silver rail with your tweezers and pull it towards yourself to take it out. Be carefull, as it still attached to the laser, just guide it slowly towards yourself.
Step 4. One comment. It's important to remove the anti-static security, otherwise it won't work!
.
Replace the laser assembly in your optical disc drive. Replacing the laser requires you to have or purchase a new laser. Flip the PlayStation 2 over so it lays with the bottom of the device facing upwards. Some models have a different number of screws and feet. Remove all the feet and screws in the bottom of the case. The 10 screw model has 6 screws in the bottom-most portion and 4 in the upper tray. Peel the warranty sticker located next to the main power switch straight away from the case. To avoid activating the VOID that may come up, heat it carefully to remove and replace it clean. To facilitate the removal, it is recommended to pry open the half closer to the power switch first while rocking the top cover towards the front of the bottom case.
Playstation 2 laser replacement
The screws on the right are a bit deeper inside the shell as like the rest but are the same size. Separate the clips at the front and the overhanging side from their mounting using a Prying Tool. With a plastic tool, lightly press down these two levers at the same time.
Who is kieron in top boy
Removing this sticker will void any warranty with Sony. Step 2. Fix Your Stuff Community Store. Single Step Full Guide. Cancel: I did not complete this guide. Carefully remove the power cord that attaches the top and bottom halves by disconnecting the power cord assembly from the top case. Add a comment. Carlos Bragatto - Feb 16, Step 3. Be carefull, as it still attached to the laser, just guide it slowly towards yourself. Peel the warranty sticker located next to the main power switch straight away from the case. Starting at the corner at which the power and Ethernet ports are located, pry open the outer shell using a spudger and continue around the entire unit. Discover the latest stuff from our wide range of partners, including exclusives only available at ZedLabz. Use this guide to help identify which optical laser lens replacement will fit your PlayStation 2 console.
Disconnect all cables from the console and flip the unit over to reveal its base.
View Statistics:. Step 3. Introduction Hi! Add Comment. If I am going through the trouble of disassembling everything then I want to make sure I have a durable replacement. Small - px Medium - px Large - px. Some lasers come without the anti-static security. Excellent guide! Some ps2 consoles have only 1 hex adjustment yet others have 2. Cancel: I did not complete this guide. Lasers will need to be fitted to the deck unit inside the console, this requires some additional rebuilding, unscrewing runners to remove the old laser and put the new one in place. This guide will explain how to replace the laser for the PS2 Slim. Gaming display stands See More "Close Cart". Add a comment.
Your phrase, simply charm
It is a pity, that now I can not express - I hurry up on job. I will return - I will necessarily express the opinion.
In my opinion it is very interesting theme. I suggest all to take part in discussion more actively.